Freight grain & Bulk load

 

Solid bulk cargo

– Any material, other than liquid or gas, consisting of a combination of particles, granules or any larger pieces of material, uniform in composition, and loaded directly into the cargo spaces without any intermediate form of containment.

The cargoes carried by bulk carriers, ranging from “clean” foodstuffs to “dirty” minerals and including those that may react with each other or with sources of contamination such as water, mean that care must be taken to ensure that cargo spaces are properly prepared for the cargo to be loaded. Cleaning must be adequate for the cargo to be loaded and will usually require a surveyor to pass the space as suitable for loading. It is essential that residues of a previous cargo are removed to ensure that contamination does not occur.

Damage to bulk cargoes is caused by water, thus, not only must the holds be dry to receive cargo, but hatch covers must be watertight or, if necessary, sealed to prevent ingress of water.

All fittings in the hold (ladders, pipe guards, bilge covers, etc.) should be examined to ensure that they are in good condition and securely fitted. Such pieces of equipment might cause severe damage to conveyor belt systems and consequent delays, for which the ship will be held liable, should they be inadvertently discharged with the cargo.

Bulk carrier, bulker

– A vessel designed to carry dry cargo, loaded into the vessel with no containment other than that of the ship's boundaries, as distinguished from the liquid bulk carrier or tanker. Conventional bulk carrier is constructed with a single deck, single skin, double bottom, hopper side tanks and topside tanks in cargo spaces.

Bulk carriers are designed to load a maximum deadweight of any type of bulk cargo from heavy ore to light grain. The loading, carriage and finally the discharge of dry bulk cargo is not as simple or straight forward as most people would imagine.

Many bulk cargoes have hazardous properties or can change their properties on passage. The ship can be easily damaged by incorrect loading e.g., loading a forward hold to it maximum can cause the ship to bend. This ‘stress’ can have life threatening results at sea in rough weather.

Residues from previous cargoes can also seriously affect latter cargoes. Water damage can also have devastated effect on some bulk cargoes e.g., cement power. It is not easy to verify true weights or quantities of cargoes loaded or discharged. All these factors have a serious consequence on the methods of operation for the safe carriage of bulk cargoes. Discharging bulk cargo using “grab”

Bulk cargoes have an inherent tendency to form a cone when they are loaded if conveyor belts, or similar systems are not supervised and controlled. The angle formed by this cone is known as the `angle of repose’ and varies with each cargo. Cargoes such as iron ore will form a steep angled cone, whereas cargoes that flow freely form a shallow angled cone. A cargo with a low angle of repose has the potential to shift during passage.

For some cargoes, bulldozers may be required to spread the load into the sides of the holds as cargo is nearing completion.

Most dry-bulk carriers depend on shoreside facilities for cargo loading and discharge, but some bulk carriers have self-unloading features with conveyors below the cargo holds, or with cranes on deck. Outlined below some of the more common bulk cargoes and their properties:

Grain

One of the most difficult and dangerous cargoes to carry in bulk are grain cargoes. Most grains have an angle of repose (slip angle) of about 20° from the horizontal, which means that if the ship rolls more than 20° the cargo will shift. Then this happens the ship will develop a large list, lying on her side and still rolling will obviously cause a greater shift of cargo which in turn will capsize the vessel.

Most authorities therefore request that the master proves that his ship is capable of remaining stable even if the grain cargo shifts. This is done by the compiling of the Grain Loading Form which fully outlines the ships stability at the worse condition on passage.

Naturally, grain cargoes, like any foodstuff, are susceptible to claims with contamination from a previous cargo and in addition can easily be damaged by water.

Vermin can also be a problem. Cargo holds must be clean and dry prior to the loading of any grain cargo and most grain charters demand a survey of the ship’s hold prior to loading for this reason.

 

Carriage of grain safe procedure - bulk carriers recommended guideline.

 

Grain, loading in bulk.

Carrying Grain:

One of the most difficult and dangerous cargoes to carry in bulk are grain cargoes. Most grains have an angle of repose (slip angle) of about 20° from the horizontal, which means that if the ship rolls more than 20° the cargo will shift. Then this happens the ship will develop a large list, lying on her side and still rolling will obviously cause a greater shift of cargo which in turn will capsize the vessel.

Most authorities therefore request that the master proves that his ship is capable of remaining stable even if the grain cargo shifts. This is done by the compiling of the Grain Loading Form which fully outlines the ships stability at the worse condition on passage.
Because grain cargoes are liable to shift, heavy emphasis is placed on the stability of ships that carry them. The main reason is the variation in the types of grain, including its size and its ability to develop a free flow state when loaded in bulk.

Each ship carrying grain must provide grain specific stability information, including grain heeling moments, to the terminal. This section looks at various problems, methods and precautions that must be taken when carrying grain cargoes. Grain cargoes carried in bags are not considered as bulk cargo.

The bulk carriers’ grain loading manual contains Volumetric Heeling Moments (VHM), which are values based on an assumed surface grain shift of 15° (for a full compartment) and 25° (for a partially full compartment).

1. To avoid shifting of cargo, the grain surfaces must be trimmed:

      dispensation is granted from trimming by the authority issuing the Document of Authorization on the basis that the cargo can flow freely to underdeck empty areas through feeder ducts, perforated decks, etc., or

      The compartment is designated a `Especially Suitable Compartment’, in which case exemption may be granted from trimming the compartment ends.

      2. If the cargo is stowed only in the lower compartment, the lower compartment hatch covers should be secured in the approved manner.

      3. If the cargo is stowed in the upper compartment above a tween deck whose covers are not grain-tight, the covers should be made grain-tight using sealing tape, tarpaulins, or separation cloths.

      4. In partly filled compartments, the surface of bulk grain should be secured by over-stowing except in cases where heeling moments due to grain shift have been calculated and taken into consideration for stability of the vessel.

      5. Longitudinal divisions may be fitted to reduce heeling moments due to shift of grain in filled compartments, trimmed, filled compartments, untrimmed and partly filled compartments, provided that each division. 

      6. The Master shall ensure that the ship:

      Corn Grain Freight Description

                    The kernel of maize has a pericarp of the fruit fused with the seed coat referred to as “caryopsis”, typical of the grasses, and the entire kernel is often referred to as the “seed”. The cob is close to a multiple fruit in structure, except that the individual fruits (the kernels) never fuse into a single mass. The grains are about the size of  peas, and adhere in regular rows round a white, pithy substance, which forms the ear. An ear can commonly hold approx. Six hundred kernels and be approx. 180 mm in length. They are of assorted colors: blackish, bluish-gray, purple, green, red, white, and yellow. When ground into flour, maize yields more flour, with much less  bran, than wheat does. It lacks the protein gluten of wheat and, therefore, makes baked goods with poor rising capability.

                    A genetic variant that accumulates more sugar and less starch in the ear is consumed as a vegetable and is called sweet corn.

                    Contamination by moults is determined by the temperature of the   grain   and the availability of water and oxygen. Moulds can grow over a wide range of temperatures, but the rate of growth is lower with lower temperature and less water availability. The interaction between moisture and temperature is important.

                    Corn usually undergoes further post-ripening after harvesting during which moisture is expelled. In this condition, the cereal is very susceptible to mold and should not yet be shipped overseas. However, as soon as the moisture content of the cereal is comparatively low (approx. 13 – 14%), adequate storage allows the sweat moisture to be absorbed by the air without the risk of mold growth. This sweating process continues for a period of approximately 1 – 2 months.

                    Applications

                    Corn is used for flour production and as a feedstuff. Starch, margarine, and edible oil are also obtained from corn.

                    Shipment / Storage

                    Corn which is “dry for shipment” may be kept for up to 12 months or longer. If the critical water content (approx. 13 – 14%) is exceeded, mold growth occurs. Corn with an excessive moisture content has a sour odor. Corn is usually shipped in bulk, rarely in bags.

                    Favorable travel temperature range: no lower limit – 20°C. Molds reach optimum activity at temperatures of between 20 and 30°C. In addition, at temperatures > 25°C, metabolic processes increase, leading to increased CO2 production and self-heating of the corn. If the cargo is transported in a hot, moist storage climate, there is a risk of premature germination. Maximum temperatures of 30°Care admissible for short periods.

                    Ventilation of cereals depends on water content: goods with a water content of < 14% and equilibrium moisture contents of < 70% do not need to be ventilated. Up to a water content of 15%, surface ventilation is recommended, to dissipate CO2, heat, and moisture. At the same time, care should be taken to ensure that the surfaces are not cooled too much, to avoid the formation of damp boundary layers beneath the cargo surface.

                    Corn releases water vapor constantly, which needs to be dissipated by ventilation. However, caution is advisable on voyages from hot to cold regions (e.g., Argentina to Europe) :
                    Corn which is not dry for shipment has a particular tendency to self-heating and the flow of heat from the cargo counteracts external cooling, so resulting in the formation of steep temperature gradients in the superficial layers of the cargo. At the same time, water vapor flows from the inside of the cargo to the surface. In the case of simultaneous cooling of the surface by ventilation, the relative humidity increases in the superficial layers of the cargo. If dry fresh air is used for ventilation, a dry surface layer several centimeters thick is obtained, which creates the impression that the cargo is free of all defects. Beneath this is then a damp intermediate layer of lower grade cereal which is starting to decompose, being stuck together, and swollen. Such damp intermediate layers are observed relatively frequently.

                    To avoid cargo damage caused by such moist intermediate layers, the fresh air supply must be restricted when there is an excessive temperature differential between the cargo and the external temperature. Damage to only a proportion of a cargo of corn is indicative of the damaged proportion having been stored in a dead air zone, where it was inadequately ventilated. Damage may also be caused by the ships’ lying in the roads at the port of destination for an extended period at low external temperatures. The cargo within the stack is, however, still at a higher temperature, resulting in water vapor transport towards the colder parts of the cargo close to the ship’s side, where moisture damage may then occur. Such damage is often associated with the fact that ventilation is stopped when the ship is lying in the roads. Ventilation is, however, essential until the cargo has been unloaded from the ship.

                    It is essential to know it is impossible to ensure proper airing throughout a  Bulk Cargo   of   cereals. Even when ventilation is carried out, the relative humidity of the immobile air between the individual cereal grains is determined by the product’s water content. For this reason, as mentioned above, drying out caused by ventilation is only superficial. As a result, cereal loaded in an excessively moist state cannot be dried and protected from spoilage by a ship’s ventilation installation.

                    It is also a fact that heat cannot be removed from a bulk stow by ventilating the top surface. Corn (maize), like most grains, is a poor conductor of heat and if deep in the bulk of the stow heat is present or being produced, only a small proportion will travel to the top and so be removed by surface ventilation. Only at the top of the stow will the temperature be that of the ventilating air. If the air of the interstices of the   grain   below the surface is warm and of high relative humidity, the effect of surface ventilation will be to cause condensation of the moisture in this air into the surface layer. This layer can then become caked and moldy to form a blanket, which will resist further removal of moisture and heat from below; and this sealing-in of heat will exacerbate the heating up process in the stow.

                    Looked upon from this point of view, ventilation is not to be recommended under any circumstances. For if the cargo below the surface is sound and of correct humidity it will remain sound and at much the same temperature as at loading. If the maize is damp and hot, ventilation – according to the usually accepted procedure – will produce a caked, wet, moldy surface layer and contribute nothing to the improvement in the condition of the bulk below.

                    It has been put forward many times that ventilation is always called for in any cargo, and that such ventilation should be continuous when the temperature of the air in the holds is more than 5°C higher than that outside, when there is a favorable differential in relative humidities and when weather conditions permit.

                    Obviously, if there is any headspace in the holds and the deck head is colder than the cargo, then ‘distillation’ will occur, and moisture will tend to be deposited on the metal work and slight ‘sweat’ falling on the cargo. Surface ventilation will assist in keeping this to a minimum. Such ventilation as is possible on-board normal cargo vessels and bulk carriers can do little more than control the small amount of moisture inevitably arising from any bulked agricultural product properly dried and matured, when it is subject to air at lower temperature than the dewpoint of the interstitial air. If the agricultural product is not properly matured and dried, then ‘auto-destruction’ will commence and there is no means on the carrying vessel to deal effectively with the internal heat produced and with any moisture arising.

                    Surface ventilation cannot cope with much rising moisture and where heavy sweat damage of corn/maize cargoes has occurred, this is undoubtedly basically due to the moisture in the cargo being above the safe carrying level, and in fact is not ‘sweat’ in the above defined sense, but it is rising moisture condensed in the cooled surface of the maize.

                    As outlined previously, corn/maize at the correct moisture content can be carried successfully without any ventilation whatsoever. However, if the moisture content of the corn/maize is above the safe carrying level, then heating up will commence and damage be occasioned. But, without ventilation, the damage will be slightly different – there being less mold and sweat damage and more fermentation effect. If there is an over stow of bags, then the rising moisture tends to condense on them and become moldy.

                    The above considerations may be expressed thus. If the moisture content of the maize at loading is above the safe carrying limit and the conditions for heating up are favorable, then with or without ventilation damage will occur in the stow. If the cargo is ventilated, then the top of the stow will become caked, moldy, and sweat damaged, with some fermentation below in the stow. If ventilation is not carried out, then the pattern of damage will be different – there being less surface caking and moldiness and more fermentation throughout the mass.

                    Risk factors

                    • Moisture/humidity
                    • Self-heating
                    • Odor
                    • Contamination
                    • Mechanical influences
                    • Toxicity / Hazards to health
                    • Shrinkage / Shortage
                    • Insect infestation / Diseases